[New May 2023] Updated 300-425 Dumps For 300-425 ENWLSD Exam

updated 300-425 dumps

For all 300-425 ENWLSD (Designing Cisco Enterprise Wireless Networks) exam candidates: Updated 300-425 dumps to help you pass one of the CCNP Enterprise Concentration exams.

Lead4Pass 300-425 Dumps provides 120 exam practice questions and answers, with PDF files and a VCE study engine for the most popular study tool of the moment to help you prepare for the 300-425 ENWLSD exam practice anytime, anywhere.

Therefore, with the help of the Lead4Pass 300-425 dumps, candidates are able to prepare for the 300-425 ENWLSD exam and finally pass the exam in the shortest possible time.

Preparing for the 300-425 ENWLSD Exam:

Download the Lead4Pass 300-425 dumps https://www.leads4pass.com/300-425.html, then practice all the questions, then you need to spend $300 to take the test and choose English or Japanese by region to prepare for the test because this test Only Both languages ​​are supported and in the end, you will be notified of your success.

Read on for the latest 300-425 Dumps exam questions:

FromNumber of exam questionsLast updatedExam name
Lead4Pass15Q1-Q13Designing Cisco Enterprise Wireless Networks (ENWLSD)
Question 14:

An engineer is configuring a centralized set of controllers for separate facilities. Which two Cisco wireless architectures must be used to ensure flexible sizing of WLAN to VLAN mappings? (Choose two.)

A. interface group

B. mobility group

C. AP group

D. controller group

E. RF group

Correct Answer: BC

Question 15:

An engineer has deployed a group of APs in an auditorium and notices that the APs are showing high cochannel interference. Which profile can be used to adjust the parameters for these high-density APs?

A. QoS profile

B. AVC profile

C. RF profile

D. ISE profile

Correct Answer: C

Reference:

Latest 300-425 dumps exam questions 15

Question 16:

APs in a remote office recently have been converted from local mode to FlexConnect to take advantage of the local switching. After the change, remote wireless users report voice quality issues and bad quality on wireless IP phones while roaming.

A debug is performed, and it is noticed that the 802.11r Fast Transition is not working as expected, like on local mode AP, though the same WLAN configuration is in place.

What is the cause of the issue regarding the FlexConnect APs?

A. They do not support 802.11r FT.

B. They must be added to AP groups along with a common RF profile.

C. They must be in a FlexConnect group to support 802.11r FT.

D. They must be added to AP groups to support fast roaming methods.

Correct Answer: C

Reference: https://www.cisco.com/c/dam/en/us/td/docs/wireless/controller/technotes/80211r-ft/b-80211r-dg.html

Question 17:

A high-density wireless network is designed. Which Cisco WLC configuration setting must be incorporated in the design to encourage clients to use the 5 GHz spectra?

A. RRM

B. Cisco centralized key management

C. Band select

D. Load balancing

Correct Answer: C

Question 18:

The wireless team must configure a new voice SSID for optimized roaming across multiple WLCs with Cisco 8821 phones. Which two settings accomplish this goal? (Choose two.)

A. Configure mobility groups between WLCs.

B. Use Cisco Centralized Key Management for authentication.

C. Configure AP groups between WLCs.

D. Configure AVC profile on new SSID.

E. Use AVC to tag traffic voice traffic as the best effort.

Correct Answer: BE

Question 19:

A customer called with a requirement that internal clients must be on different subnets depending on the building they are in, AH access points are operating in local mode and will not be modified, and this is a single-controller solution. Which design approach creates the desired result?

A. Create an SSID, place it to the desired VLAN under WLANs, and configure 802 lx in ISE to assign the correct VLAN based on the SSID from which the client is authenticating.

B. Create FlexConnecI groups, place the access points in. and set the correct VLAN to SSID mapping based on location.

C. Create AP groups for each desired location, map the correct VLANs to the internal SSID, and add the access points for that location.

D. Create mobility anchors for the SSID, and on the controller under the internal SSID. Create a foreign map to the desired VLAN based on location.

Correct Answer: C

Question 20:

DRAG DROP

Drag and drop the characteristics from the left onto the correct functionalities on the right.

Select and Place:

Latest 300-425 dumps exam questions 20

Correct Answer:

Latest 300-425 dumps exam answers 20

Question 21:

A high-density wireless network is designed. Which Cisco WLC configuration setting must be incorporated in the design to encourage clients to use the 5 GHz spectra?

A. Band Select

B. RRM

C. Cisco Centralized Key Management

D. load balancing

Correct Answer: A

Reference:

Latest 300-425 dumps exam questions 21

Question 22:

A wireless engineer is designing a wireless network to support real-time applications over wireless. Which IEEE protocol must the engineer enable on the WLC so that the number of packets that are exchanged between an access point and client are reduced and fast roaming occurs?

A. 802.11w

B. 802.11r

C. 802.11i

D. 802.11k

Correct Answer: B

Question 23:

An engineer is designing a new wireless network. The network needs to meet these requirements:

Latest 300-425 dumps exam questions 23

Which design approach should be taken?

A. 5 GHz frequency band with channel bonding, to support 40 MHz channels

B. 5 GHz frequency band without channel bonding, to support 20 MHz channels

C. 5 GHz frequency band with channel bonding, to support 80 MHz channels.

D. 2.4 GHz frequency band without channel bonding, to support 20 MHz channels

Correct Answer: B

Reference: https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/108184-config-802-11n-wlc.html

Question 24:

An enterprise is using two wireless controllers to support the wireless network. The data center is located in the head office Each controller has a corporate WLAN configured with the nameCopr-NET390595865WLC-1 and CoprNET6837l638WLC-2. The APs are installed using a round-robin approach to load balance the traffic.

What should be changed in the configuration to optimize roaming?

A. Move all access points to one controller and use the other as N+1 HA.

B. Move the controllers to an external data center with higher internet speeds.

C. Use the same WLAN name for the corporate network on both controllers.

D. Place the access points per floor on the same controller.

Correct Answer: C

Question 25:

Refer to the exhibit.

Latest 300-425 dumps exam questions 25

An enterprise has offices spread around the globe. The APs are connected to different controllers installed in separate data centers. The IT team wants to allow clients to roam from controllers in group ABC to controllers in group XYZ. Which feature must be incorporated in the design to accomplish this task?

A. switch peer group

B. workgroup bridge

C. mDNS gateway

D. mobility lists

Correct Answer: D

Question 26:

An enterprise is using the wireless network as the main network connection for corporate users and guests. To wireless network availability.

Two Standalone controllers are installed in the head office. APs are connected to the controllers using a round-robin approach to load balance the traffic.

After a power cut, the wireless clients disconnect while roaming. An engineer tried to ping from the controller but failed. Which protocol needs to be allowed between the networks that the controllers are installed?

A. IP Protocol 67

B. IP Protocol 77

C. IP Protocol 87

D. IP Protocol 97

Correct Answer: D

Reference:

Latest 300-425 dumps exam questions 26

Question 27:

What is the recommended cell overlap when designing a wireless network for Cisco Hyperlocation?

A. 20%

B. 30%

C. 40%

D. 50%

Correct Answer: A

Reference:

Latest 300-425 dumps exam questions 27

Question 28:

A wireless engineer must optimize RF performance for multiple buildings with multiple types of construction and user density. Which two actions must be taken? (Choose two.)

A. Configure Flexconnect groups for each building.

B. Configure WMM profiles for each building.

C. Configure AP groups for each area type.

D. Configure RF profiles for each area type.

E. Enable DTPC on the network.

Correct Answer: CD

Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-10/config-guide/b_cg810/configuring_ap_groups.html


Visit: https://www.leads4pass.com/300-425.html Use the complete 300-425 Dumps exam questions to pass the 300-425 ENWLSD exam prep. Good luck!